Roll-forming equipment for shed production, configured to your profile drawings and trial-run before shipment.
We supply the forming equipment a shed factory runs every day: the panel line for roof and wall sheets, the purlin machine for the frame, the double-layer roll former for a second profile, and the trim roll former for flashings and trims.
Whether you are setting up a new line, adding a profile or replacing a worn machine, we configure the equipment to your drawings and handle it through to your port.
A complete line that turns galvanised or pre-painted coil into roof and wall sheets: decoiler, feeding table, forming stands, hydraulic cut-to-length and run-out table, under PLC control. Built to your profile — trapezoidal, corrugated or tile-effect.
| Reference profile | Roof sheet, 1015 mm cover width |
|---|---|
| Material | 0.4–0.8 mm galvanised steel, 550 MPa |
| Decoiler | 5 t hydraulic, coil width up to 1250 mm |
| Forming stations | 20 |
| Forming speed | 15–20 m/min; flying-cut version up to 40 m/min |
| Cutting | Hydraulic cut-to-length, ±2 mm |
| Control | PLC with touch screen |
| Power supply | 415 V / 50 Hz / 3-phase (customisable) |
One line for the structural members of garages, farm sheds and light warehouses. On PLC-change models, section type and size are switched from the control panel instead of swapping spacers by hand; punching is set to your purlin drawings.
| Sections | C, Z and U purlins; C/Z and C/U interchangeable models |
|---|---|
| C purlin web | 80–300 mm |
| Z purlin web | 120–300 mm |
| Material thickness | 1.5–3.0 mm |
| Forming speed | 8–25 m/min |
| Size change | PLC-controlled, 3–5 minutes; manual version available |
| Punching | Web holes, flange holes and custom patterns |
| Cutting | Hydraulic shear; flying shear optional |
Two profiles from one machine. Two sets of forming rollers sit on an upper and a lower deck, so a factory can make two different roof or wall profiles in the floor space of a single line. One deck runs at a time.
| Layout | Upper and lower deck, one profile each; clutch-selected |
|---|---|
| Profiles | To your drawings: trapezoidal, corrugated, tile-effect |
| Material | 0.3–0.8 mm galvanised, aluminium-zinc or pre-painted coil |
| Forming speed | 15–20 m/min |
| Example configuration | Upper deck 1100 mm cover-width profile (18 passes) + lower deck 980 mm cover-width profile (22 passes) |
| Cutting | Hydraulic post cut-off for both decks |
| Control | PLC with touch screen |
Roll-forms two sizes of flashing or trim profile on one line, with inline pre-punching and a hydraulic cut-off.
| Profiles | Two trim sizes on one line (reference model: U50 / U75) |
|---|---|
| Material | 0.8–1.2 mm galvanised steel |
| Forming stations | 16, plus vertical side rollers |
| Pre-punching | Inline punching station |
| Size change | Manual, via split sleeves |
| Speed | Up to 15 m/min, excluding punching and cutting time |
| Cutting | Hydraulic post cut, one blade set per profile, ±1 mm |
| Control | PLC with touch screen |
Figures are reference configurations. Profile, thickness range, voltage and options are confirmed for each order against your drawings.
We match machine type and configuration to your profile drawings, thickness range and output.
Each machine is run on your profile before it leaves; sample sheets are sent for your approval.
Seaworthy packing, with container loading supervised by us.
We book the freight and prepare the export documents through to your port.
We reply within two working days with a sourcing plan and an indicative quotation.
